Preparing your files for mixing and mastering

A mix starts well before the first listen: it starts the moment you export your tracks. Clean, complete and well-named files mean time spent on the music instead of on tidying up a session. This guide covers what we ask for on every project, with the technical reasons behind each instruction.

As soon as we receive them, we check your files and get back to you within 48 hours. If something is missing or causes a problem, you know before the work begins.

Contents

For mixing

Format: WAV or AIFF, 24-bit, at the session sample rate

Export as WAV or AIFF, at 24-bit (or 32-bit floating point if you prefer). Keep your session’s sample rate: if you recorded at 48 kHz, export at 48 kHz. A sample rate conversion adds nothing and can degrade the signal; we prefer to work on the original files.

No MP3, no AAC, no files extracted from a video: a compressed format has already removed part of the information, and it can’t be recovered at the mix.

Export: every track from the same starting point

Every track must start at exactly the same place, at the very beginning of the session (bar 1 or 0:00), even if the instrument only comes in at the second chorus. All tracks therefore have the same length. Opened in a new session, they line up by themselves, with no manual shifting.

Allow a few seconds after the last note so reverb and delay tails can die away.

Export mono sources as mono (vocal, bass, kick, guitar recorded with a single mic) and stereo sources as stereo (synthesizers, stereo pianos, ambient mic pairs). A vocal exported as stereo only contains the same signal twice: it doubles the file size and adds nothing.

Level: peaks between -6 and -4 dBFS

No track should reach 0 dBFS. Aim for peaks between -6 and -4 dBFS: at 24-bit, a few decibels of margin cost nothing in quality, whereas a clipped peak is permanent.

Don’t normalize your tracks and don’t try to make them loud. The relative level between instruments is set at the mix.

Effects: send the tracks dry, plus the effects that are part of the sound

Switch off the equalizers, compressors and reverbs you added to get an idea of the mix: we will redo them with our own processing.

Do keep the effects that are part of the track’s identity: a rhythmic delay on the vocal, distortion or an amp simulation on the guitar, a chorus, a flanger, a deliberately processed voice. In that case, send two versions of the track, with and without the effect (Vocal.wav and Vocal_FX.wav). If the new effect doesn’t suit you, the original is still available.

If a vocal needs tuning, the pitch correction option (+€30, on mixing) takes care of it: send the take as it was sung.

Naming: the instrument name, as short as possible

A file name should say what it contains without having to listen. Give the instrument name directly, as short as possible, and add a detail only when several sources of the same type coexist (the mic, the part, the side):

Kick_In.wav
Kick_Out.wav
Snare_Top.wav
Snare_Bottom.wav
HiHat.wav
OH_L.wav
OH_R.wav
Bass.wav
Guitar_1.wav
Guitar_2.wav
Piano.wav
Synth.wav
Vocal.wav
Vocal_FX.wav
BV_L.wav
BV_R.wav

No track numbers: the order is set in our session. Avoid accents, spaces and special characters: depending on the system, they become unreadable once the archive is unzipped. Ban “Audio 1_04.wav” and other “final bounce v3” names.

Tempo, key and intentions

Attach a short text file (Notes.txt) with:

  • the tempo (BPM) and, if it varies, a tempo map or a MIDI file of the click track;
  • the key, and the time signature if it isn’t 4/4;
  • your intentions: the mood you are after, what should stand out, what bothers you in your current version;
  • if you like, one or two reference tracks that suit your song, with what you like in each (“the vocal placement”, “the low end”, “the space”);
  • your rough mix, meaning your own mix as it is today, exported in stereo from the session;
  • your demo version: the track as you finished it yourself, with your own mastering, even a rough one.

The rough mix matters a lot: it shows the balance you are used to and the details you have built and want to keep.

For mastering

Mastering works on a single file: your stereo mix. Everything before it is fixed, which is why the export matters.

  • Format: a stereo WAV or AIFF file, at 24-bit or 32-bit float, at the session sample rate.
  • Level: peaks between -6 and -4 dBFS, and never above 0 dBFS.
  • Master bus: no limiter or maximizer. If the limiter is part of your sound, send two versions, with and without. Bus compression or EQ that “glues” the mix can stay, if it is set with restraint.
  • Start and end: leave a little silence before the first note and after the last one. Don’t cut the end: send the whole track and describe the fade you want in your notes, we will do it at mastering.
  • A reference: a track whose sound speaks to you, and a few words on what you expect from it.
  • Your demo version: the track as you finished it yourself, with your own mastering, even a rough one. It shows us what you have in mind.

Why between -6 and -4 dBFS?

These numbers aren’t magic. They simply guarantee that the mix hasn’t been clipped or crushed before reaching the studio. Mastering needs this margin to shape the dynamics with our compressors, rather than starting from a signal that is already flattened.

Careful: lowering the master fader of an already limited mix doesn’t create headroom. You get a limited mix, just quieter. It’s the limiter that has to go.

44.1 or 48 kHz?

Keep the sample rate the track was produced at. We deliver by default at 44.1 kHz / 24-bit, and at another sample rate, up to 96 kHz, on request.

An EP or an album

Send all tracks at the same sample rate and include:

  • the running order;
  • the transitions you want (a pause between two tracks, tracks linked with no silence);
  • the exact titles, as they will appear on streaming platforms.

For stem mastering

Stem mastering starts from a few instrument groups rather than a single stereo file. It lets you fix at mastering what a stereo file no longer lets you touch separately: a vocal sitting a little back, a low end that spills over.

  • 4 to 8 stems, for example: drums, bass, instruments, lead vocal, backing vocals, effects.
  • Format: WAV, 24-bit (or 32-bit float), at the session’s original sample rate.
  • Same starting point and same length for all, as for a mix.
  • No processing on the master bus at export.
  • Level: the peaks of the sum of the stems should sit between -6 and -4 dBFS, never above 0 dBFS.
  • Your demo version: the track as you finished it yourself, with your own mastering, even a rough one. It shows us what you have in mind.
  • The sum of the stems must reproduce your mix. To check, import them into an empty session, all faders at 0 dB, and compare with your mix: you should hear the same thing.
  • Reverbs and delays: either they stay in the stem of their source, or they are grouped in an “Effects” stem. Both work, as long as the sum matches the mix.
  • Sidechain: if the kick makes the bass breathe through sidechain, check that this effect is present in the bass stem. When soloed, the sidechain source is sometimes muted and the effect disappears.

Exporting from your software

Choose your software: the settings to tick are shown for mixing (separate tracks) and for mastering (stereo mix). Menus change from one version to the next: these pointers guide you, your software’s manual is the reference.

Sending your files

  1. Gather tracks, rough mix, demo version, references and notes in a folder named Artist_Title_BPM (for example Kayo_Late_Night_125BPM).
  2. Compress this folder into a ZIP.
  3. Once your order is paid, send the archive through WeTransfer to contact@rectapestudio.com.

Don’t send your files as an email attachment: they are too heavy and may never arrive.

We acknowledge receipt, check the files and get back to you within 48 hours if something needs fixing.

The checklist

To tick before sending. One PDF checklist per type of service: Stereo mastering · Stem mastering · Mixing & Mastering

Mixing

  • WAV or AIFF, 24-bit or 32-bit float, at the session sample rate
  • All tracks start at the beginning of the session and have the same length
  • Mono sources as mono, stereo sources as stereo
  • No peak at 0 dBFS, peaks between -6 and -4 dBFS
  • Working processing switched off; creative effects supplied with and without
  • Tracks named simply, without numbers (Kick_In.wav, Vocal.wav)
  • Rough mix exported in stereo
  • Notes: tempo, key, intentions, references

Mastering

  • Stereo mix as WAV or AIFF, 24-bit or 32-bit float, original sample rate
  • Peaks between -6 and -4 dBFS, never above 0 dBFS
  • No limiter on the master bus (or two versions: with and without)
  • Full ending, no cut-off fade; wanted fade described in the notes

Stem mastering

  • 4 to 8 stems as WAV, 24-bit (32-bit float), original sample rate
  • Same start and same length for all stems
  • Master bus with no processing
  • Sum of the stems checked: it reproduces the mix
  • Peaks of the sum of the stems between -6 and -4 dBFS

Sending

  • Artist_Title_BPM folder compressed into a ZIP
  • Your demo version: the track finished by you, with your own mastering (even a rough one)
  • A listening reference if you like
  • For an EP or an album: running order, transitions, exact titles
  • WeTransfer to contact@rectapestudio.com

The most common mistakes

  1. Tracks exported from their first sound: they no longer line up with each other.
  2. A limited mix sent to mastering: the lost dynamics don’t come back.
  3. MP3 or resampled files: the starting quality is already damaged.
  4. Tracks named “Audio 1_04”: every file has to be listened to find out what it contains.
  5. A track clipped at export: digital clipping is permanent.

Preparation FAQ

How much headroom should I leave for mastering?

Peaks between -6 and -4 dBFS, with no limiter on the master bus. What matters isn’t the exact figure, but that the mix hasn’t been clipped or over-compressed.

Should I normalize my tracks?

No. Normalization changes the level of each file without improving anything, and loses the level relationships of your session.

Should I leave the limiter on the mix?

No. If it is part of the sound you want, send two versions, with and without: we will compare.

How many tracks does my project have?

Count each audio file you send us, mono or stereo. A project of 18 files falls in the 17 to 32 tracks bracket. Prices per bracket are on the Pricing page.

Are your files ready?

Start your project online, or write to the studio about an album, a film or a restoration.